JBL Stadium 10 Marine Speaker Owner’s Manual

JBL-logo

JBL Stadium 10 Marine Speaker

JBL-Stadium-10-Marine-Speaker-Product

THANK YOU FOR YOUR PURCHASE 
Your JBL product has been designed to provide you with the performance and ease of operation you would expect from JBL.
ABOUT THE MANUAL
This manual describes general installation guidelines. However, please note that proper installation of marine audio components requires qualified experience. If you do not have the knowledge and tools to successfully perform this installation, we strongly recommend consulting an authorized JBL dealer about your installation options. Keep all instructions and sales receipts for reference.

WHAT’S IN THE BOX

JBL-Stadium-10-Marine-Speaker-fig-1

DIMENSIONSJBL-Stadium-10-Marine-Speaker-fig-2
JBL-Stadium-10-Marine-Speaker-fig-3SPEAKER SIGNAL WIRING

To send signal to the JBL manne speaker, connect the positive(+) and negative(-) speaker wires to the appropriate speaker outputs of your source unit or amplifier. Be sure to observe proper polarity. JBL-Stadium-10-Marine-Speaker-fig-4

SPEAKER LED WIRING

To provide power for the LEDs, plug the 24-gauge black(+), blue, green, and red LED wires from the speaker into the included female connector, then run the wires from the female connector to your compatible 12-volt power source or light controller (sold separately). If using a separate controller, be sure to connect each wire to the proper output. JBL-Stadium-10-Marine-Speaker-fig-5

If hardwiring the LEDs directly to your power source, you can choose the color of the LEDs by connecting the black wire to the positive (+) terminal, and the appropriate R, G, and/or B single wire or combination of wires to the negative (-) terminal. There are 7 possible colors, depending on the wiring configuration you choose:

Wire connected to positive (+12V) terminal The wire connected to negative (-) terminal Color produced
 

 

 

 

 

Black

Red Red
Green Green
Blue Blue
Red+ Green Yellow
Red+ Blue Purple
Blue+ Green Aquamarine
Red + Blue + Green White                                       –

APPLYING FOAM SEAL

To help seal your installation against water, and to provide an airtight acoustic seal, apply the self-adhesive foam seal to the speaker frame. JBL-Stadium-10-Marine-Speaker-fig-6

MOUNTING THE SPEAKER

Use the included screws to mount the speaker to the location. Use the included speed clips if necessary to provide a secure mount.
NOTE: Use caution when cutting and using screws with fiberglass to prevent scratches and cracks. JBL-Stadium-10-Marine-Speaker-fig-7

REMOVING THE TWEETER FOR SEPARATE MOUNTING (STADIUM 8 ONLY)

Use the included 2-pin tool to remove the tweeter from the woofer housing. Place the pins of the tool in the holes of the tweeter grille and rotate 45 degrees clockwise to loosen and remove. JBL-Stadium-10-Marine-Speaker-fig-8

FLUSH-MOUNTING THE TWEETER

Place the tweeter in the mounting bracket and use the tool to secure by turning 45 degrees counter-clockwise. JBL-Stadium-10-Marine-Speaker-fig-9

To transmit audio signal to the tweeter, make sure the woofer and tweeter are connected with the included cable. JBL-Stadium-10-Marine-Speaker-fig-10

Place the tweeter in the mounting location, then turn each setscrew clockwise to tighten the mounting brackets. Use caution so as not to overtighten. Snap the included outer ring over the mounting bracket to hide the setscrews. JBL-Stadium-10-Marine-Speaker-fig-11

MOUNTING IN AN ENCLOSURE (STADIUM 10 ONLY)

JBL-Stadium-10-Marine-Speaker-fig-12

SEALED-BOX VOLUME (INCLUDES DRIVER DISPLACEMENT) JBL-Stadium-10-Marine-Speaker-fig-13

Size Tuning frequency
Free air 40Hz
2 ft3 (56.6L) 52.2Hz
3 ft3 (85L) 48.3Hz
4 ft3 (113L) 46.3Hz

VENTED-BOX VOLUME (INCLUDES DRIVER DISPLACEMENT)JBL-Stadium-10-Marine-Speaker-fig-14

Size Port length Port diameter Tuning frequency
2 ft3 (56.6L) 7-9/32″ (185mm) 3-15/16″ (100mm) 41Hz
3 ft3 (85L) 5-1/2″ (140mm) 3-15/16″ (100mm) 40.6Hz
4 ft3 (113L) 4-1/4″ (108mm) 3-15/16″ (100mm) 40.4Hz

Technical Data

TECHNICAL DATA

THIELE-SMALL PARAMETERS

Stadium Marine 10(250mm) Subwoofer 2-ohm Stadium Marine 10″ (250mm)

Subwoofer 4-ohm

Voice coil DC resistance: Rev(OHMs) 1.96 3.7
Electrical inductance: lc:Es (mH) 10.49 17.52
Driver radiating area: SD (CM2) 356.33 356.33
Motor force factor: Bl (TM) 8.953 11.491
Compliance Volume: VAS (Liters) 23.5 23.8
Suspension compliance: CMS (mm/N) 0.131 0.133
Moving mass, air load: MMS (Grams) 107.338 106.389
Moving mass, without air load: MMD (Grams) 99.737 98.789
Free-air resonance: F5 (Hz) 42.5 42.4
Mechanical 0:  

OMS

9.913 4.025
Electrical 0:  

O ES

0.699 0.793
Total 0:  

OTS

0.653 0.663
SPL, 1W/1m @ 4ohm: Lm {dB) 86.14 85.62

Specifications

Specifications Stadium 6 Stadium 8 Stadium 10
Continuous power handling 100W 200W 300W
Peak power handling 300W 500W 900W
Frequency response 40Hz-25kHz 30Hz-22kHz 20Hz- 2kHz
Nominal impedance 3 Ohms* 3 Ohms* 2 or 4 Ohms (use switch to select)
Sensitivity 92dB 92dB 89dB
External diameter 7-15/32″ (189.4mm) 9-1/2″ (241mm) 11- 5/8″ (295.3mm)
Mounting cutout diameter 5-23/32″ (144.8mm) Woofer: 7″ (177.4mm) Tweeter bracket: 4-9/16″

{115.9mm)

9-9/16″ (235.6mm)
Total depth 3-21/32″ (92.5mm) 4-5/8″ {117.2mm) 6-9/16″ {167mm)
Mounting depth 2-9/16″ (65mm) 3-3/16″ (80.5mm) 4-7/8″ {123mm)

HARMAN International Industries, Incorporated 8500 Balboa Boulevard, Northridge, CA 91329 USA www.jbl.com

Documents / Resources

JBL Stadium 10 Marine Speaker [pdf] Owner’s Manual
109STADM62, Stadium 6, Stadium 8, Stadium 10, Marine Speaker, Stadium 10 Marine Speaker

References

Leave a Comment